Displaying 1-20 of 35 resources
Resource Type: Website / HyperLinkWeld Competency Chart-G Joiner
Grades: No grades selected.Subjects: Manufacturing & Product DevelopmentChart of required welds for capstone level courseContributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkEgg Dragsters, 1 of 4 by Jeff Kirby
Grades: 11 to 12Subjects: Manufacturing & Product DevelopmentThis is the first of four lessons that have students design and build a metal car to carry an egg down a steep hill and survive.Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkOxy-Fuel Welding Basics, Principles, and Safety
Grades: No grades selected.Subjects: Manufacturing & Product DevelopmentBy Justin Pickard This lesson will take students through the basic concepts, principles, and safety of oxy-fuel Welding. This i...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkProject Squaring.
Grades: No grades selected.Subjects: Manufacturing & Product DevelopmentBy: Tom Boyes This is designed to reinforce the importance of starting with a square project.Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkMetal Project Planning
Grades: No grades selected.Subjects: Manufacturing & Product DevelopmentBy: Matt Joiner This document provides the student, instructor, and parents with a clear understanding of the intended project....Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkCareers
Grades: No grades selected.Subjects: Manufacturing & Product DevelopmentBy: Jerry Joiner Local careers in welding as seen on a power point presentation.Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkTorch Cutting
Grades: No grades selected.Subjects: Manufacturing & Product DevelopmentBY: Matt Joiner This lesson is designed to introduce the student to the specific techniques of both freehand and guided (use of...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkAngle grinder usage
Grades: No grades selected.Subjects: Manufacturing & Product DevelopmentBy: Jerry Joiner The student will learn the correct usage and safety of angle grinders by following along with the handout and...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkWorld War I Tommy Bi- Plane
Grades: No grades selected.Subjects: Manufacturing & Product DevelopmentBy: Tom Boyes By the end of this lesson students will have learned the basic draw commands that are needed to cut out the parts...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkReading the Welding Symbol
Grades: No grades selected.Subjects: Manufacturing & Product DevelopmentBy: Gregg Bridges This lesson introduces the AWS welding symbol to students and explains how to decipher all the information giv...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkCh. 5 Fitting and Jigging
Grades: No grades selected.Subjects: Manufacturing & Product DevelopmentBy FRED SCHUTZ Welder's Handbook, Ch. 5, Fitting and Jigging. Students will read, be lectured to, and tested on Ch. 5. Students...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkBuilding Blocks - Metal for Welding and Machining
Grades: 9 to 12Subjects: Manufacturing & Product DevelopmentThis lesson introduces students to basic types of metals and metal forms (sheets, rods, bars, angles) used in general fabricatio...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkSMAW Weld Joint Fit Up
Grades: No grades selected.Subjects: Manufacturing & Product DevelopmentProper various Groove joints fit upContributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkMetal Bench-Tom Boyes
Grades: No grades selected.Subjects: Manufacturing & Product DevelopmentThis is a project that can be given as a first Fabrication project. This lesson will challenge the entry-level student to make a...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkWelding Equipment-Schutz
Grades: No grades selected.Subjects: Manufacturing & Product DevelopmentCh. 3 Welding Equipment By FRED SCHUTZ Chapter 3 of the Welder's Handbook, Welding Equipment will be read and reviewed in class....Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkAbrasive Cutoff Saw Usage by Steve Gambril
Grades: No grades selected.Subjects: Manufacturing & Product DevelopmentStudents will learn to properly and safely use the cutoff saw and know the importance of proper adjustments.Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkWelding Career Research
Grades: No grades selected.Subjects: Manufacturing & Product DevelopmentThis assignment is designed to introduce the Metals 1 student to a variety of welding careers and the requirements/training need...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkEgg Dragsters 2 of 4 by Jeff Kirby
Grades: No grades selected.Subjects: Manufacturing & Product DevelopmentThis lesson will go over the design of the egg dragster and how the design is governed by the material choices in the lab.Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkEgg Dragsters: 3 of 4 by Jeff Kirby
Grades: No grades selected.Subjects: Manufacturing & Product DevelopmentThis lesson will cover the construction of the egg dragster.Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkStriking an Arc / Maintaining an Arc by Gregg Bridges
Grades: No grades selected.Subjects: Manufacturing & Product DevelopmentThis lesson will teach beginning welding students how to set up the SMAW welding machine, how to strike an arc, how to maintain ...Contributor: CTE OnlineViews: 0Favorites: 0