Displaying 101-120 of 206 resources
Resource Type: Website / HyperLink**Perform a battery, starter, charging system test using the VAT-40 (updated) by Eli Jaramillo
Grades: No grades selected.Subjects: TransportationOverview: Using correct go/no-go specifications and a VAT- tester, students will load test vehicle battery, starter and chargi...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkAnimation Fuel Injectors (updated) by John Potter
Grades: No grades selected.Subjects: TransportationThis lesson covers how fuel injectors deliver fuel in different modes: Sequential and Simultaneous. It is designed to get the st...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLink**Inspection and Pressure Testing of Cooling System (updated) By Jose Sanchez
Grades: No grades selected.Subjects: TransportationIn this lesson, students will participated in a cooling system inspection and testing.Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLink**Ingredient 3: Ignition (updated) by Thomas Dougherty
Grades: No grades selected.Subjects: TransportationUpon completion of this session, students will have an understanding of how a primary ignition signal is generated and be able t...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLink**Ingredient 2: Compression (updated) by Thomas Dougherty
Grades: No grades selected.Subjects: TransportationUpon completion of this session, students will be able to identify air movement events in relationship with mechanical events wi...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLink**Ingredient 1: Fuel (updated) by Thomas Dougherty
Grades: No grades selected.Subjects: TransportationUpon completion of this session, students will be able to explain how the fuel/air charge is created, how it enters the cylinder...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLink**Ingredients to Internal Combustion (updated) by Thomas Dougherty
Grades: No grades selected.Subjects: TransportationUpon completion of this lesson, students will be able to demonstrate knowledge of the four stroke cycle and the ingredients to i...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLink**Charging System Fundamentals (updated) by Russell Granger
Grades: No grades selected.Subjects: TransportationIntroduce students to the operational theory and practical service techniques of the automotive charging system. Students will b...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLink**Starting System Fundamentals (updated) by Russell Granger
Grades: No grades selected.Subjects: TransportationIntroduce students to the operational theory and practical service techniques of the automotive starting system. Students will b...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLink**Catalytic Converter (updated) by Richard Williams
Grades: No grades selected.Subjects: TransportationThis is an introductory lesson into the construction, operation and the diagnostic techniques used for the common automobile cat...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLink**Bore & Stroke (updated) by John Potter
Grades: No grades selected.Subjects: TransportationThis in an introduction to what is Bore and Stroke; the meaning of short and long, larger and small; and to introduce the meanin...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLinkIgnition System Service (updated) by Curt Erales
Grades: No grades selected.Subjects: TransportationStudents will learn to diagnose and repair ignition problems. Students will learn that there are some common problems to look fo...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLink**The 4 strokes of an engine (updated) by Curt Erales
Grades: No grades selected.Subjects: TransportationThis lesson is designed for entry level students to understand the four strokes of an engine and how a 4 stroke engine functions.Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLink**How to make a gasket using a ball-peen hammer (updated) by Ramon C. Iniguez
Grades: No grades selected.Subjects: TransportationOccasionally, technicians are faced with a situation where a job is being held-up because a simple gasket is on back order. Rat...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLink**Car Wash Procedures (updated) by Robin Coyne
Grades: 9 to 12Subjects: TransportationEvery car needs to be regularly washed as part of the maintenance program for that vehicle. This lesson is designed to allow any...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLink**Labor Time vs Labor Dollars (updated) by John Potter
Grades: 9 to 12Subjects: TransportationThis is an activity to show how to convert labor time in minutes to labor time in dollars using basic math. The use of addition,...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLink**Parts and Labor (updated) by John Potter
Grades: 9 to 12Subjects: TransportationFollowing the Repair Order Documentation excercise. This lesson concentrates on the math and proper placement of parts and labor...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLink**Technician and School Certification (updated) by James P. Lane
Grades: No grades selected.Subjects: TransportationIn this lesson, students will use the Internet to explore and locate accurate information regarding certification programs and t...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLink**Broken Bolt Extraction Methods Part 1 (updated) by Robert Thayer
Grades: No grades selected.Subjects: TransportationThe instructor will demonstrate the need, theory, key terms and techniques of broken bolt extraction. At the end of the lesson, ...Contributor: CTE OnlineViews: 0Favorites: 0
Resource Type: Website / HyperLink**Using taps to cut metric and standard threads (updated) by Ramon C. Iniguez
Grades: No grades selected.Subjects: TransportationStudents will use common hand and power tools to drill and tap metric and standard threads on a piece of metal.Contributor: CTE OnlineViews: 0Favorites: 0